Sti 1221 Bedienungsanleitung
Stöbern Sie online oder laden Sie Bedienungsanleitung nach Zubehör für elektrische Sti 1221 herunter. STI 1221 Manuel d'utilisation Benutzerhandbuch
- Seite / 2
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Safety Technology International, Inc.
2306 Airport Road • Waterford, Michigan 48327-1209
Phone: 248-673-9898 • Fax: 248-673-1246
Toll Free: 800-888-4784 • E-mail: [email protected]
Web: www.sti-usa.com
Safety Technology International (Europe) Ltd.
Unit 49G Pipers Road • Park Farm Industrial Estate • Redditch
Worcestershire • B98 0HU • England • Tel: 44 (0) 1527 520 999
Fax: 44 (0) 1527 501 999 • Freephone: 0800 085 1678 (UK only)
E-mail: [email protected]om • Web: www.sti-europe.com
INSTALLATION OF STI-1221B STROBE DAMAGE STOPPER
®
All specifications and information shown were current as of publication and are subject to change without notice.
INSTALLATION NOTES
1. Damage Stopper must be installed to comply with applicable NEC, NFPA and local codes.
2. In areas where frequent wash downs occur, standoff blocks must be used.
3. In applications where wash downs, rainfall or condensation occur, it is recommended
that a drain or weep hole be provided. Refer to weep hole installation diagram.
4. Damage Stopper may be installed outdoors when appliance carries an outdoor rating.
Electronic warranty form at www.sti-usa.com/wc14
1221BIS APRIL2006
CLEANING INSTRUCTIONS
Rinse with water to remove
abrasive dust and dirt. Wash with
soap or mild detergent, using a
soft cloth (do not scrub). Rinse
once more then dry with a soft
cloth or chamois. To remove
grease or wet paint, rub gently
with a cloth wetted with naphtha.
Then wash and rinse.
DO NOT USE RAZOR BLADES.
INSTALLATION INSTRUCTIONS - REFER TO EXPLODED VIEW
1. Insert the (4) 06297T external mounting tabs into the frame
assembly slots.
2. Using back box assembly as a template, place against
mounting surface at proper location according to NFPA 72.
3. Mark and drill (4) holes 1/4 in. (6.3mm) diameter,
1 1/4 in. (32mm) deep.
4. Insert the (4) anchors into the wall.
5. Mount back box to wall with screws.
6. Install electrical fittings as needed.
7. Install strobe appliance.
8. Install cover with clips and screws.
9. Test appliance according to appliance manufacturer’s
instructions.
1
2
19013 SCREW #10 x 1 1/2 in.
(4) PROVIDED
629764 CLAMP
(4) PROVIDED
19033 ANCHOR
(4) PROVIDED
06297T EXTERNAL
MOUNTING TABS —
INSERT TABS INTO FRAME
SLOTS AS SHOWN
TYPICAL NOTIFICATION
APPLIANCE
OPTIONAL CONDUIT HUB
SUB-6297B20
(ACCEPTS 3/4 in. RIGID
CONDUIT FITTINGS)
INCLUDES GASKET AND
MOUNTING HARDWARE
IF ADDED PROTECTION IS
NEEDED DUE TO ENVIROMENTAL
CONDITIONS ORDER SUB-122
ENVIRO KIT
629763 STANDOFF BLOCKS
(4) MUST BE USED IN AREAS
WHERE FREQUENT WASH DOWNS
OCCUR SUPPLIED WITH SUB-122
ENVIRO KIT
HEIGHT
8.5 in.(216mm)
DEPTH
3.5 in.(89mm)
WIDTH
6.5 in.(165mm)
BACK OF FRAME
ASSY. MAY BE DRILLED
TO ALLOW WIRE ACCESS
AS SHOWN
LOCATED IN THIS AREA
DRILL 1/4 in. (6mm) DIA.
APPROX.
CENTER LINE
OF UNDERSIDE
OF COVER
1 in.(25mm)
01221 COVER ONLY
!
01221 COUVERCLE SEULEMENT
19047 #8-32 x 3/8 in. SOCKET
HEAD CAP SCREW (4) PROVIDED
06297B FRAME ASSY.
1
2
19013 SCREW #10 x 1 1/2 in.
(4) PROVIDED
629764 CLAMP
(4) PROVIDED
19033 ANCHOR
(4) PROVIDED
06297T EXTERNAL
MOUNTING TABS —
INSERT TABS INTO FRAME
SLOTS AS SHOWN
TYPICAL NOTIFICATION
APPLIANCE
OPTIONAL CONDUIT HUB
SUB-6297B20
(ACCEPTS 3/4 in. RIGID
CONDUIT FITTINGS)
INCLUDES GASKET AND
MOUNTING HARDWARE
IF ADDED PROTECTION IS
NEEDED DUE TO ENVIROMENTAL
CONDITIONS ORDER SUB-122
ENVIRO KIT
629763 STANDOFF BLOCKS
(4) MUST BE USED IN AREAS
WHERE FREQUENT WASH DOWNS
OCCUR SUPPLIED WITH SUB-122
ENVIRO KIT
HEIGHT
8.5 in.(216mm)
DEPTH
3.5 in.(89mm)
WIDTH
6.5 in.(165mm)
BACK OF FRAME
ASSY. MAY BE DRILLED
TO ALLOW WIRE ACCESS
AS SHOWN
LOCATED IN THIS AREA
DRILL 1/4 in. (6mm) DIA.
APPROX.
CENTER LINE
OF UNDERSIDE
OF COVER
1 in.(25mm)
01221 COVER ONLY
!
01221 COUVERCLE SEULEMENT
19047 #8-32 x 3/8 in. SOCKET
HEAD CAP SCREW (4) PROVIDED
06297B FRAME ASSY.
INSTALL CLAMP IN NOTCH 2 AS SHOWN
INTERNAL DIMENSIONS
WEEP HOLE INSTALLATION
REMARQUES SUR L’INSTALLATION
1. Le Stopper de dégâts doit être installé de sorte à être conforme avec les normes NEC,
NFPA applicables et les codes locaux.
2. Dans les zones où des jets d’eau fréquents surviennent, des blocs de détection à
distance doivent être utilisés.
3. Dans les applications où des jets d’eau, des précipitations ou de la condensation se
produisent, il est recommandé de prévoir un trou de vidange ou une barbacane.
Reportez-vous à schéma d’installation d’une barbacane.
4. Il est possible d’installer un Stopper de dégâts à l’extérieur lorsque l’appareil est
homologué pour utilisation à l’extérieur.
1
2
Inhaltsverzeichnis
Seite 1 - REMARQUES SUR L’INSTALLATION
Safety Technology International, Inc.2306 Airport Road • Waterford, Michigan 48327-1209Phone: 248-673-9898 • Fax: 248-673-1246Toll Free: 800-888-4784
Seite 2 - STI-1210 / STI-1221 SERIES
• This enclosure is rated to protect signaling appliances indoors and in areas of indirect weather exposure.The cover may be used outdoors only with d
Weitere Dokumente für Zubehör für elektrische Sti 1221
Sti 1221 Bedienungsanleitung
(2 Seiten)
Verwandte Produkte und Handbücher für Zubehör für elektrische Sti 1221
(2 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 1.217 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern