INSTALLATION OF STI-6517 STI STOPPER
®
STATION SHIELD
All specifications and information shown were current as of publication and are subject to change without notice.
6517 MARCH2010
Safety Technology International, Inc.
2306 Airport Road • Waterford, Michigan 48327-1209
Phone: 248-673-9898 • Fax: 248-673-1246
Web: www.sti-usa.com
Safety Technology International (Europe) Ltd.
Unit 49G Pipers Road • Park Farm Industrial Estate • Redditch
Worcestershire • B98 0HU • England • Tel: 44 (0) 1527 520 999
Fax: 44 (0) 1527 501 999 • Freephone: 0800 085 1678 (UK only)
E-mail: info@sti-europe.com • Web: www.sti-europe.com
INSTALLATION NOTES
1. Insert Sounder/Wireless PCB into PCB Card Guides on Stopper Station Cover.
2. Orient the Button Lever so it is pointed toward the inside of the Stopper Station Shield Assembly.
3. With Shield Rotated to open position (Approximately 90° to Cover), insert Shield Pivots into Slots on
Stopper Station Cover.
4. Rotate Cover to Closed Position.
5. Rotate Cover to fully open position, back to closed position, and ensure the Button Level is pressed
down onto the button. If not, repeat steps 2-5.
6. Program the sounder volume on or off by pulling off the plastic battery tab with the battery remaining
installed. (Sounder will be on at this point)
7. The sounder volume programming cycle is ON for 10 seconds, OFF for 10 seconds, and then defaults to
ON. To set volume: open the Shield, close, open again and close again.
NOTE: Remove and replace battery to reset volume setting.
8. Mount Shield, Cover and PCB Assembly onto Stopper Station Button Assembly.
9. Install Screw to Hold Cover to Button Assembly.
4.84 in.
(123mm)
5.32 in.
(135mm)
1.76 in.
(45mm)
3.51 in.
(89mm)
STOPPER STATION
SHELL
STOPPER STATION
CONTACT ASSEMBLY
STOPPER STATION
SHIELD
STOPPER STATION SHELL
WITH NOTCHED SLOTS
(FOR SHIELD PIVOTS)
SCREW
STOPPER STATION
CONTACT ASSEMBLY
SOUNDER PCB
123A LITHIUM BATTERY
PCB GUIDE
COVER MOUNTING SLOTS
BUTTON LEVER
SHIELD PIVOT
STOPPER STATION SHEILD
STOPPER STATION COVER
4.84 in.
(123mm)
5.32 in.
(135mm)
1.76 in.
(45mm)
3.51 in.
(89mm)
STOPPER STATION
SHELL
STOPPER STATION
CONTACT ASSEMBLY
STOPPER STATION
SHIELD
STOPPER STATION SHELL
WITH NOTCHED SLOTS
(FOR SHIELD PIVOTS)
SCREW
STOPPER STATION
CONTACT ASSEMBLY
SOUNDER PCB
123A LITHIUM BATTERY
PCB GUIDE
COVER MOUNTING SLOTS
BUTTON LEVER
SHIELD PIVOT
STOPPER STATION SHEILD
STOPPER STATION COVER
4.84 in.
(123mm)
5.32 in.
(135mm)
1.76 in.
(45mm)
3.51 in.
(89mm)
STOPPER STATION
SHELL
STOPPER STATION
CONTACT ASSEMBLY
STOPPER STATION
SHIELD
STOPPER STATION SHELL
WITH NOTCHED SLOTS
(FOR SHIELD PIVOTS)
SCREW
STOPPER STATION
CONTACT ASSEMBLY
SOUNDER PCB
123A LITHIUM BATTERY
PCB GUIDE
COVER MOUNTING SLOTS
BUTTON LEVER
SHIELD PIVOT
STOPPER STATION SHEILD
STOPPER STATION COVER
Electronic warranty form at www.sti-usa.com/wc14
(1 Seiten)
(1 Seiten)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern